Maintenance Technician

Job Posting Title

Maintenance Technician

Job Description Summary

This position is accountable for: Providing support to the plant by means of repair, replacement, and/or renewal of equipment or components. Any activity necessary within the scope of skills within the principal accountabilities for this position and those of General Maintenance position. Completing assigned documentation, maintain cleanliness of maintenance shop and other work areas.

Job Description:

Key Responsibilities:

• Follow all health, safety and environmental practices and preventative measures.

• Follow rules and procedures.

• Electrical/Robotics

• Resolve circuit level problems, install additional circuits and provide sketches or drawings of proposed changes.

• Monitor PLC programs for troubleshooting machinery.

• Maintain power distribution system (480 VAC and under) including troubleshooting, new installation, changing fuses, replacing bus duct and bus plugs

• Troubleshoot robotics and teach points as required

• MIllright

• Move, level, and verify readiness to run

• Hydraulics

• Resolve system problems, recommend and install additional components as needed

• Machine Rebuilding

• Assume responsibilities for assigned areas of a project and execute trade skills as required.

• Preventative Maintenance

• Preforms PM's as assigned, complete and return all documentation

• Work with contractors to complete PM's

• Trouble Shooting

• Follow and document the basic guidelines for failure analysis

• Call, communicate with, follow recommendations of, and document activity from a service representative

• Component failure analysis, i.e. megger, wear pattern, contamination's, etc.

• Document all results on the work order

• Reports on Maintenance Technician Work

• Provide accurate reports of work performed on work order in appropriate maintenance software

• Regularly report to cover 100% of day

• Drive forklift in a safe manner

• Complete Electronic Operator Lift Truck Functional Check on every shift for every forklift driven that shift unless already completed on shift.

• Change propane tanks as required for fork trucks.

• Charge fork truck batteries as required on electric fork truck.

• Actively participate in Continuous Improvement and perform them as scheduled.

• Participate in training as required.

• Clean during and end of shift.

• Maintain work area and equipment in a neat and orderly fashion.

• Complete records and forms as required and instructional documents.

• Perform duties at all times in a safe and efficient manner and report problems, irregularities and suggested corrective action immediately to supervisor.

• All other associated maintenance duties as assigned in accordance to the CBA.

Soft Skills and Other Competencies:

• Ability to follow directions.
• Knowledge of LEAN tools.
• Knowledge of basic problem-solving tools such as Root Cause and 5-why.
• Skills in operating office equipment, such as personal computer, calculator, and copier.
• Ability to communicate with employees and business contacts in a group or individual setting.
• Ability to prioritize duties and good time-management skills.
• Ability to work directly with all levels of the organization in a fast-paced environment
• Detail oriented.
• Ability to read and write the English language.

Safety and 5-S Requirements:

Accidents involving injuries, property damage, and spills must be reported immediately. Near misses (close calls) are also important for loss control and must be reported as well. Lean Enterprise 5-S standards must be maintained in all assigned areas.

Environmental Conditions:

This position will experience a wide range of conditions. From office conditions to actual shop floor exposure. There is no condition that exists that this position will not be exposed to

Personal Protection Equipment:

Must be worn, when required in specific areas. Includes, but is not limited to Safety Glasses with side shields, Hearing Protection and Safety Shoes.

Required Skills and Education

Minimum score of 70% on knowledge (including both practical and written) test chosen by GKN Sinter Metals or completion of approved apprenticeship program

High School Diploma/GED

Valid Forklift License (This is obtained at GKN), valid articulated scissor lift license and Genie Boom.

Necessary eye and muscular coordination to perform job.

About Dauch:

Dauch Corporation is a premier Driveline and Metal Forming supplier serving the global automotive industry with a powertrain-agnostic product portfolio that supports electric, hybrid, and internal combustion vehicles. The company is headquartered in Detroit, MI, with operations that span 24 countries and more than 175 locations. Formed through the acquisition of Dowlais Group plc and its subsidiaries - GKN Automotive and GKN Powder Metallurgy, Dauch unites deep engineering roots with global manufacturing capabilities and an entrepreneurial spirit to move mobility forward. Visit www.dauch.com to learn more.

Dauch will not discriminate against any Associate or applicant for employment because of age, race, color, gender, religion, weight, height, marital status, sexual orientation, genetic history or information, gender identity or expression, disability, protected veteran status, national origin, or other characteristic protected by law. Dauch will take affirmative action to ensure that applicants are employed, and that Associates are treated equally during employment, without regard to their age, race, color, gender, religion, weight, height, marital status, sexual orientation, genetic history or information, gender identity or expression, disability, protected veteran status, national origin, or other characteristic protected by law. For the Disabled Job Seeker: We offer reasonable accommodations for qualified disabled individuals who are applicants for employment. To request assistance or accommodations, please e-mail TalentAcquisition@aam.com. Dauch is an equal opportunity/affirmative action employer.