New Exciting Level II Quality Control Inspector in Hampton!
Job Duties:
Perform receiving, in-process, first-piece, and final inspections of purchased material, machined components, fabricated parts, assemblies, and finished product to verify conformance to drawings, specifications, travelers/routers, work instructions, and applicable customer and internal quality requirements.
Verify that the correct revision of drawings, specifications, planning, and supporting documentation is available and being used at the point of inspection.
Use appropriate inspection, measuring, and test equipment to verify dimensional, visual, and workmanship requirements in accordance with defined acceptance criteria.
Confirm material identification, certification, and traceability are present and properly maintained when required by contract, customer flowdown, internal procedure, or product risk.
Verify completion and accuracy of required inspection records, operation sign-offs, certifications, and supporting objective quality evidence applicable to the inspection scope.
Ensure only properly identified and, where applicable, calibrated inspection equipment is used for product acceptance activities.
Accurately document inspection results, including inspection reports, checklists, acceptance records, nonconformance records, and reinspection results.
Identify, document, and communicate nonconforming product; ensure suspect or nonconforming material is properly identified, segregated, and controlled in accordance with internal procedures.
Support containment, reinspection, verification of rework/repair, and corrective action implementation activities as assigned.
Support customer, source, or third-party inspection activities when assigned, including presentation of relevant inspection records and objective evidence.
Maintain legible, complete, and objective quality records in accordance with internal procedures and applicable customer, statutory, regulatory, and quality management system requirements.
Perform inspections using established procedures, checklists, work instructions, and defined acceptance criteria.
Escalate unclear requirements, discrepancies, or inspection issues to higher-level inspectors or supervision.
Document inspection findings accurately and completely under guidance.
Demonstrate basic proficiency in inspection tools, measuring devices, and visual inspection methods required for assigned work.
May observe or assist with Complex Measurement Equipment activities under direct supervision, but is not independently authorized to set up, run, interpret, or report results from such equipment.
Support production by identifying obvious defects, workmanship issues, and documentation gaps.
Independently perform more complex inspections requiring interpretation of drawings, specifications, revision requirements, traveler/router content, and acceptance criteria.
Apply inspection judgment to determine conformity within assigned authority and ensure required records and objective evidence are complete before product acceptance.
Initiate and document nonconformance records with clear, technically accurate descriptions of the condition identified and the affected requirement.
Support troubleshooting and containment activities by providing inspection input to production, engineering, and quality personnel.
Mentor and assist Level 1 inspectors in proper inspection techniques, documentation expectations, and handling of nonconforming product.
When qualified and authorized, independently set up and operate approved Complex Measurement Equipment using established procedures, approved programs, fixtures, and routines, and record standard outputs and raw data.
Identify obvious out-of-tolerance conditions from Complex Measurement Equipment outputs and escalate technical interpretation, report generation, or method concerns as required.
Qualifications:
Relevant inspection, machining, fabrication, welding, manufacturing, or quality experience required at a level appropriate to the position. Higher levels require demonstrated progression in technical capability, judgment, documentation quality, and independence in a controlled manufacturing environment.
Ability to read and interpret engineering drawings, specifications, revision requirements, travelers/routers, and acceptance criteria; use common inspection and measuring equipment; document results accurately; and identify nonconforming conditions. Experience with blueprint reading, GD&T, inspection reports, certifications, traceability records, and objective quality evidence is strongly preferred.
High school diploma or equivalent required. Technical school, trade training, or relevant coursework in manufacturing, machining, fabrication, welding, blueprint reading, metrology, or quality is preferred.
Schedule:
Monday-Friday 7am-3:30pm
Pay:
$24.00-$30.00 per hour
Numbers & Facts
Location
Hampton, VA
Salary
$24–$30 Per Hour
Skills
Blueprintsunmatched
Corrective Actionunmatched
Customer Support/Serviceunmatched
Documentationunmatched
Documentation Planunmatched
Engineering Drawingunmatched
Geometric Dimensioning and Tolerancingunmatched
High School Diplomaunmatched
Identify Issuesunmatched
Machiningunmatched
Manufacturingunmatched
Mentoringunmatched
Metrologyunmatched
Network Routersunmatched
Procedure Developmentunmatched
Production Supportunmatched
Purchasing/Procurementunmatched
Quality Controlunmatched
Quality Managementunmatched
Quality System Requirements (QSR)unmatched
Riskunmatched
Statutory Lawsunmatched
Test & Measurement Equipmentunmatched
Traceabilityunmatched
Weldingunmatched
Willing to Travelunmatched
🎯
Be found by employers
5,500+ employers search our resume database daily. Add yours to get found by recruiters looking for candidates like you.
Level up your application
Professional resume templates
Browse dozens of recruiter approved resume templates, layouts and formats. Choose your favorite and make it your own in minutes.